MICRO MOLEX CONNECTOR PLUS

So, what crimping tool is appropriate for these Micro-Fit pins?ĭon't know what other Molex is in my future in my -12 build. Here are some tools I've been able to locate but not sure if they handle the right size: USB 2.0 and Micro-B offer an IP67-rated waterproof option that withstands. Many consumer and industrial applications experience wet conditions that could cause failure in connectors. I saw a reference to a specific tool hnere but that was a general Molex discussion and can't tell whether it covers the Micro-Fit pins. With 3.0A/5.0A current to enable faster and safer charging, Molex offers a wide range of USB Type-C Connectors that are physically robust and electrically reliable. The problem is, the pins provided in the kit don't identify the size. They all seem to accommodate at least three sizes just judging from the picture. I've been through most of the Molex threads and don't seem much smarter than I was before. I'm trying to find the right tool to crimp the Micro-Fit pins for the pitch trim servo (page 11-07). If I know I can get a small cutter back on the connecters after installation I will sometimes use tie-wrap to secure them together if there is insufficient room for back-shells but, without a back-shell, there may not be enough strain relief on the wires in case the bundle gets pulled. Too much solder and the pin won't insert.įor low-amp stuff (< 3A 14V) I now use D-SUB connector. There are only two locations to crimp: the outer one that captures the wire jacket and the next one in that makes contact with the stripped wire.įinally, I like to hit the inner crimp with a tiny bit of solder - but only after I'm happy with the crimp, not in lieu of a good crimp. If you crimp those it both deforms the pin making it hard to insert and prevents it from latching into the molex housing because you've destroyed the latching flanges. I've found my most common mistake is to accidentally crimp the latching flanges that splay out from the pin or barrel housing at about a 30 degree angle. Headers, eliminating the need for customers to make major revisions or investments in their applications.Those pins are fussy. Mini-Fit TPA2 Receptacles are backward compatible with Mini-Fit Jr. Mini-Fit TPA2 Connectors prevent end-product failure by offering terminal position assurance (TPA), which reduces terminal back-out by providing locking redundancy. The impact of terminal back-outs can result in liability costs to manufacturers and harm to individuals.

Incorrectly assembled connectors can lead to terminal back-outs, causing end-product failure.

Furthermore, they feature flanges that help “gather” the mating receptacle for more accurate mating. Mini-Fit BMI Connectors allow misalignment and provide up to 2.54mm of float between mating surfaces for easy blind-mate connections.

MICRO MOLEX CONNECTOR PLUS

and Mini-Fit Plus Connectors are compatible with each other, including with Mini-Fit TPA2 and Mini-Fit BMI Components, bringing flexibility to the toughest design dilemmas.Ĭustomers with blind mate applications require connectors that make assembly easier, protect against mis-mating and prevent potential damage to terminals. To meet these needs, Mini-Fit Jr., Mini-Fit Plus, Mini-Fit Blind-Mate Interface (BMI) and Mini-Fit TPA2 Connectors offer polarized housings with isolated terminals, positive locks and low-engagement forces. Provides excellent support for the rubber cap that mounts around the back of the housingĪllows for accurate mating to standard Mini-Fit 4.2 Power ConnectorsĪ wide range of OEMs require high-current, high-density power connectors that also support design flexibility. Provides safety, and stability of housing to the pane and Ultra-Fit Power Connectors offer premium housing features to prevent mismating, reduce terminal backout and reduce operator fatigue during assembly. Panel mount ears recommended panel cut-outs for 0.89mm to 3.00mm thick panels panel cut-out tolerances +0.10mm: Various connector challenges can result in end-product failure: mismated connectors, terminal backout and other assembly errors. Provides safety for the terminals during packing and assembly insertion Mini-Fit Sigma Offer redundant, secondary current paths for long-term performance and reliability Prevents accidental unmating Mini-Fit Blind Mate Interface (BMI) ConnectorsĪllows 2.54mm misalignment in x and y axis for all configurations Mini-Fit Max (Single and Dual Row)ĭelivers more power per linear inch and square millimeter than other mid-range power connectors Enables operator to mate connectors in hard to reach areasĮnsures header and receptacle cannot be mismatedĮasy to operate thumb latch assures connectors are fully mated

Micro molex connector